Residential Control Systems TXB16 Manual do Proprietário Página 235
- Página / 329
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 19 Thermostats 221
Wait 0:00:10.00 with timer #1 (Thermostat Request Timer)
Request Zone 3 Temperature Report
End Wait
Refresh Zone ## System Mode
Refresh Zone ## Fan Mode
Refresh Zone ## Temperature Setting
These commands "refresh" the specified thermostat (from 1 to 16) setting. "Refresh" means that the
controller looks at the current setting (a system variable maintained inside the controller) and sends
the same command to the thermostat.
This command can be used to ensure that the thermostat is in the desired state. If the thermostat
has been changed manually and the controller does not know it, this will put the thermostat back into
the old state.
Thermostat Data Commands
These thermostat data commands operate on the thermostat system variables, described below.
Thermostat System Variable Summary
The controller has 64 internal "system" variables that it uses to hold the thermostat data. Each of the 16
available zones has these four variables:
Current Temperature
: The zone's current temperature. For zones 1 and 2, this is the temperature
reading that is displayed on the TV Thermostat Control Screen. This value can
be changed in the following two ways:
- By a command in your schedule (perhaps after reading the temperature
from a temperature sensor).
- By the thermostat reporting a new temperature setting to the controller. Of
course, this is only possible if the thermostat can report its temperature (like
the RCS TX10-B and TX15-B or serial thermostats can).
Temperature Setting
: The zone thermostat's temperature setting. For zones 1 and 2, this is the
temperature setting that is displayed on the TV Thermostat Control Screen.
This setting can be changed in the following ways:
- From the TV Thermostat Control Screen.
- By a command in your schedule.
- By the thermostat reporting a new temperature setting to the controller.
- If the controller is running the zone to a time/temperature schedule, this
variable will be set to the desired temperature at the scheduled time (and
the setting will also be transmitted to the thermostat).
Zone Configuration
: This variable stores the thermostat type and house code for the zone. It can
only be changed from the Thermostat Configuration Screens in the PC software
and video menu system.
Zone Status
: This variable stores the current operating modes of the zone. Three different
modes are tracked and stored in this variable:
- HVAC system mode (Heat, Cool, Auto, or Off)
- Fan mode (On or Auto)
- Control mode (Run or Hold)
- HomeVision 1
- CONTENTS 3
- APPENDICES 13
- CHAPTER 1: INTRODUCTION 15
- On-Line Help 16
- Creating A Schedule 17
- How to Get Started 18
- Manual Conventions 18
- Safety Tips 19
- Program Overview 21
- Main Menu 21
- Program Screen Descriptions 22
- Object/Event Summary Screens 22
- Editing Actions 24
- Object Initial States 24
- Action Entry Screen 25
- Toolbar 26
- Configuration Screens 27
- Control Screens 31
- X-10 Control Screen 32
- X-10 Grid Control Screen 32
- Macro Control Screen 33
- IR Control Screen 33
- Video Control Screen 34
- Thermostat Control Screen 34
- Advanced Screens 35
- Other Screens 36
- Terminal Emulator Screen 37
- IR Learn Screen 37
- IR Test Screen 37
- Serial Command Test Screen 38
- Status Screen 38
- View Messages Screen 39
- Read Event Log Screen 39
- Debug Tools Screen 39
- CHAPTER 3: QUICK START 41
- 3) Install PC software 42
- 4) Run PC software 42
- 9) Verify X-10 operation 43
- 10) Verify video output 43
- Actions 47
- Conditions 47
- If-Then-Else Statements 48
- Entering Conditions 49
- Compound Conditions 49
- Evaluation Logic 49
- CHAPTER 5: X-10 53
- X-10 Event Triggers 54
- X-10 Codes 54
- X-10 Signal Transmissions 55
- X-10 Transmission Settings 56
- X-10 Lighting Scenes 57
- Creating Scenes 57
- Executing Scenes 58
- X-10 Commands 59
- X-10 Control Commands 61
- Advanced X-10 Commands 61
- X-10 Command Details 62
- X-10 Conditions 71
- X-10 Sequences 73
- Use Of Module Enable/Disable 74
- Time And Date Conditions 77
- Time Conditions 78
- Date Conditions 78
- CHAPTER 7: SCHEDULED EVENTS 81
- Scheduled Event Commands 82
- Scheduled Event Conditions 83
- CHAPTER 8: PERIODIC EVENTS 85
- Periodic Event Commands 86
- Periodic Event Conditions 87
- General Timer Operation 89
- Timer Operating Modes 90
- Standard Timers 90
- Wait Timers 91
- Timer Commands 93
- Timer Conditions 95
- Examples 97
- CHAPTER 10: FLAGS 99
- Flag Commands 100
- Standard Flag Commands 100
- Advanced Flag Commands 100
- Flag Conditions 101
- Power Failure Options 102
- CHAPTER 11: VARIABLES 103
- Math Commands 104
- Variable Commands 104
- Standard Variable Commands 104
- Other Variable Commands 107
- Advanced Variable Commands 109
- 16-Bit Variable Commands 110
- Variable Conditions 111
- Introduction 113
- Input Port Event Triggers 113
- Detailed Port Description 114
- Input/Output Port Locations 114
- Port A - Relay Drivers 115
- Port A Examples 116
- Adding Transient Suppression 117
- External Power Source 117
- External Relays 118
- Controller 118
- Terminal Block 1 118
- Port B - Digital Inputs 119
- Port B Examples 121
- Port C Output Examples 123
- External 124
- Terminal Block 3 124
- #9 or #10 125
- Control Of Output Ports 126
- Output Port Commands 126
- Set Output Port Low 127
- Set Output Port High 127
- Toggle Output Port 127
- Disable Output Port 128
- Enable Output Port 128
- Output Port Conditions 129
- Control Of Input Ports 130
- Input Port Commands 130
- Advanced Input Port Commands 131
- Input Port Conditions 132
- Output Port Notes 132
- Use Of Output Enable/Disable 132
- Input Port Notes 133
- CHAPTER 13: VIDEO SYSTEM 135
- Built-In Video Menu System 136
- Video Screens Overview 136
- Start Video Menu System 139
- Display Screen ## 139
- Event Log 140
- Thermostat Screens 140
- Weather Conditions Screen 140
- Custom Menu System 140
- Overview 140
- RAM Video Screens 142
- Displaying RAM Video Screens 143
- Using The RAM Video Screens 144
- Text Storage Buffer 144
- Video Commands 146
- Video Configuration Commands 146
- Start Internal Video Mode 147
- Start External Video Mode 147
- Stop Video Mode 147
- Video Switch 148
- OSD Circuit 148
- OSD Switch 148
- Video Control Commands 149
- Video Text Commands 151
- Event Log Commands 155
- Infrared Simulation Commands 155
- Video Conditions 157
- Display Video Screen #0 158
- Clear Screen 158
- Infrared Signal Description 159
- Standard Infrared Signals 160
- Other Infrared Signals 161
- IR Signal Reception Details 161
- Learning IR Signals 166
- “CheckOnAndOffTimes” Setting 167
- “CheckFirstPulse” Setting 167
- “Tolerance” Setting 167
- Electrical Connections 169
- IR Transmitting 170
- IR Transmit 170
- Entering IR Signal Actions 175
- IR Transmission Settings 175
- IR Signal Commands 176
- IR Signal Conditions 177
- Clock Adjustment 179
- Controller Commands 179
- Reporting Commands 179
- Operating Modes Commands 181
- Other Commands 183
- Controller Conditions 186
- If TW-523 OK 188
- If TW-523 Error 188
- Data Terminator 191
- How to Receive Serial Data 192
- Controller Report Messages 195
- Command Responses 196
- Serial Commands 197
- Serial Receive Commands 200
- Serial Conditions 203
- Playing Wave (WAV) Files 205
- Writing To Text Files 208
- Clear text file log.txt 209
- Close comm port 210
- HV Desktop Control Program 212
- Serial Port Forwarding 213
- CHAPTER 17: MACROS 215
- Macro Conditions 216
- CHAPTER 18: CALLER ID 217
- Stop Video Mode 218
- End Wait 218
- Caller ID Log 219
- Caller ID Name Lookup 219
- Caller ID Commands 220
- Caller ID Conditions 221
- CHAPTER 19: THERMOSTATS 223
- Built-In Thermostat Control 224
- RCS TX10 And TX15 Thermostat 228
- Reading X-10 Thermostat Data 229
- Automatic X-10 Data Requests 230
- Advanced Thermostat Control 231
- Thermostat-Related Commands 231
- Thermostat Commands 232
- Thermostat Data Commands 235
- Thermostat Conditions 237
- EnerZone StatNet Thermostats 238
- Custom Thermostat Control 238
- IO-8O8I Setup 240
- IO-8O8I/485 Setup 240
- Using The I/O Boards 242
- Digital Temperature Sensors 242
- DS1820 Connection Modes 243
- Connections 243
- Software Configuration 244
- Port Numbering System 245
- CHAPTER 21: DATA LOGGING 247
- Data Logging Conditions 249
- Using The Data Log 249
- Writing To The Data Log 249
- Reading From The Data Log 250
- CHAPTER 22: WEATHER DATA 253
- Temperature Variables 254
- Relative Humidity Variables 254
- Wind Variables 255
- Rainfall Variables 255
- Weather Data Commands 256
- CHAPTER 23: TELEPHONE 257
- Installation And Setup 259
- 3) Connect Serial Port 260
- Security System Commands 261
- Security System Events 262
- Security System Conditions 263
- CHAPTER 25: INTERNET ACCESS 267
- Configuration 268
- User name and password 269
- ?ACCESS=password 270
- FLAGUPDATE:009001110100 271
- </FORM> 285
- Remote Internet Access 286
- Server Configuration 286
- Client Configuration 287
- Using Remote Internet Access 287
- Remote Internet Access Notes 288
- CHAPTER 26: MISCELLANEOUS 289
- Remote Modem Control 291
- Making a Remote Connection 293
- Additional Modem Notes 295
- Exporting Schedule Data 296
- Section Name 297
- Section Format 297
- Complete Example 299
- Front Panel LEDs 300
- Specifications 301
- Connectors 302
- Dynamic Data Exchange (DDE) 303
- Control Style 303
- Controller Error Messages 304
- IR Receive Problem 311
- IR Transmit Problem 312
- Video Problem 312
- X-10 Interface Cable Problem 314
- X-10 Receive Problem 314
- X-10 Transmit Problem 315
- APPENDIX D: WARRANTY 329
Manuais e produtos relacionados com Termóestatos Residential Control Systems TXB16
(20 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais